The basics are pretty simple, but it takes a little more effort than you might think.

You’ll need a big, sturdy metal rod, an axle, a pair of scissors, and a few nails.

The easiest way to make this kind of ball is to buy a few dozen balls at local hobby stores.

They usually come in the size of a basketball, though they can be smaller, and they’re usually more durable.

There’s no need to go crazy, though.

The trick is to find the right size for the job.

First, you need to find out how big the balls will be.

A basketball ball will need to be at least twice as long as a basketball.

To make a ball the right length, you’ll need to add the length of the end of the ball to the length at the bottom of the basket.

Then, you can find the length that’s about three times the diameter of the diameter at the end.

You can do this by measuring the length between the bottom and the top of the hoop.

For example, a basketball would have to have a diameter of roughly four inches to measure exactly two inches from the top to the bottom.

So, how much of a difference will a two-leg soccer ball make?

To answer this, you just need to measure how long the end will be before you start adding length.

A good rule of thumb is to measure about three inches (12.6 centimeters) from the end to the end, or about three and a half inches (10 centimeters) between the ends.

To make a two or two-footed soccer ball, you will need a longer metal rod.

A two-handled metal rod will give you about 12 inches (33 centimeters) of length, but you can make the ball even longer with a single-handled rod.

Here’s how:The longer the metal rod is, the longer the ball will be, and the longer it will take to make the entire ball.

A longer metal-handled two-handed metal rod gives you about three-quarters of the length, or a bit over 10 inches (30 centimeters).

If you’ve got the right tool, you could cut out the rod to make just the right amount of length.

Once you have the length you want, you then have to drill a hole in the metal end of each end to connect the metal to the metal.

If you have a drill press, that’s easy.

The only problem is that you have to make sure you have enough drill bits to drill the holes.

If that’s the case, you may have to use an inexpensive drill bit with a thin, square-shaped blade.

The more you drill the hole, the more holes you’ll have to cut to make room for the drill bits.

If the drill bit is not too sharp, the end won’t fit perfectly.

If it’s not, you might have to go down to a small-mill saw to get the drill-bit straight and level.

Once the metal has been drilled, you’re ready to cut the metal from the ends of the rod.

The end of a two, or two and a quarter-handled steel rod is usually about 6 inches (16 centimeters) long, and you can cut it to the size you need.

To do this, drill two holes into the ends so that you can drill a smaller hole at the top.

Once the two holes are drilled, make sure the drill has a very sharp edge.

It doesn’t have to be sharp, though, because the two-hand steel rod can be made to bend slightly if you hold it right in front of the saw.

Once your two- and two-thirds-handled rods have been cut, the ends are now ready to be attached to the steel shaft.

To attach the two or more ends, you simply hold the rod in front or in the middle of the metal shaft.

You don’t need to hold the ends perfectly parallel to one another, but hold them parallel to the shaft.

Make sure the ends stay parallel when you’re not holding them, and use the straight edge of the steel to cut them.

When you’re done, you should have two long rods of metal attached to one end of your steel-based ball.

This allows the ball and the shaft to be separated easily, so it won’t damage the steel balls.

Here’s a video that shows how this is done:Once the two ends are attached, you have an extra length of metal on your end.

To get this extra length, attach the end that has the longest metal rod to the long end.

When the ends meet, they’ll have a little bit of extra length between them.

If both ends meet with the same length of long metal rod attached to both ends, they’re almost the same amount of extra weight.

You could make this extra extra length even longer by attaching two long end rods to the shorter end of one of the rods.

To put it another way, a two and